This tutorial is a sequel of of Matteo Lissandrini's "Installing HDFS and Hadoop 2.X on a Multi-node cluster with Ubuntu 14.0.
That guide can also be used to install Hadoop 1.x (with minor if none modification); in this work we will assume that you have followed that tutorial and have installed Hadoop 1.x and HDFS.
Even thought HBase 0.94.x can run against both Hadoop 1.x and 2.x versions (see HBase 0.94 book) we highly recommend to use Hadoop 1.x for HBase 0.x and Hadoop 2.x for HBase 1.x and 2.x.
We wish also to inform you that also this tutorial can be applied to HBase 1.x and 2.x (with minor if none modification).
The following steps will be needed only once. Download HBase 0.94.X stable, to do so navigate in the List of Mirrors select one and decide which version to download. For the sake of simplicity from now on we will assume tho have chosen version 0.94.27.
For example wget can be used:
# from eu wget https://www.eu.apache.org/dist/hbase/hbase-0.94.27/hbase-0.94.27.tar.gz # from us wget https://www.us.apache.org/dist/hbase/hbase-0.94.27/hbase-0.94.27.tar.gz
Then extract the tar to the final installation directory, fix also permission and create a version agnostic symlink.
In this tutorial we will use the standard /usr/local/ as installation directory but obviously you are free to chose the one you prefer.
# extract & copy sudo tar -zxf hbase-0.94.27.tar.gz -C /usr/local/ # fix permission sudo chown -R hduser:hadoop /usr/local/hbase-hbase-0.94.27/ # create symlink sudo ln -s /usr/local/hbase-0.94.27/ /usr/local/hbase
It is vital to distinguish the DF049 from its cousins. If you are buying parts, a simple mix-up can cost hundreds.
| | Typical DF049 Meaning | Commonly Affected Models | | :--- | :--- | :--- | | Automatic Transmission | Fault in internal pressure regulation (often DP0/AL4 gearbox) | Laguna II, Scénic II, Mégane II | | Air Conditioning (A/C) | Refrigerant pressure sensor circuit malfunction (open/short circuit) | Mégane II, Scénic II, Clio III | | Fuel System | Incorrect fuel pressure detected by the ECU | Various models with fuel system issues | | Electronic Parking Brake | Application force not reached, sensor or motor fault | Laguna III, other models with EPB | | Other Systems | Coolant sensor circuit, wiring issues, control module faults | Scénic II, Mégane II, other models |
The automatic transmission relies on precise hydraulic pressure to engage clutches and bands for smooth gear changes. When pressure deviates from expected values, the Transmission Control Module (TCM) logs DF049. Common causes include: df049 renault
A: Yes, short distances. But prolonged driving with active limp mode can cause catalytic converter damage or increased turbo wear due to incorrect mixtures.
The sensor requires a 5V feed from the ECU; if this is missing, the code will persist even with a new sensor. How to Diagnose and Fix It It is vital to distinguish the DF049 from its cousins
Once you've identified the likely system, perform focused inspections:
The vehicle feels sluggish or unresponsive. Unusual Transmission Noise. Common Causes of DF049 The sensor requires a 5V feed from the
Start by checking the transmission fluid level and quality. The DPO transmission does not have a dipstick; it requires a specialized level check procedure. Check for any obvious leaks from the transmission case or driveshaft seals. If the fluid is dark or smells burnt, it needs replacement. 2. Inspect the Solenoids and Wiring
Finally configure and initialize the other cluster nodes.
List the machines that will act as region server in conf/regionservers,
one address per line line.
If needed update /etc/hosts according to Hadoop tutorial hints.
Once done, propagate the setup throw the cluster:
#!/bin/bash
# Build configured HBase tar.
mkdir -p /tmp/distr/
tar -czf /tmp/distr/hbase.tgz /usr/local/hbase-0.94.27
# Distribute to each region node
while IFS='' read -r node_ip; do
scp /etc/hosts hduser@$node_ip:~/
scp ~/.profile ~/.vimrc hduser@$node_ip:~/
scp hbase.tgz hduser@$node_ip:~/
ssh -o StrictHostKeyChecking=no -tt hduser@$node_ip <<EOF
sudo mv $HOME/hosts /etc/
# Install & link & fix permission
sudo tar -zxf $HOME/hbase.tgz -C /
sudo ln -s /usr/local/hbase-0.94.27 /usr/local/hbase
sudo chown -R hduser:hadoop /usr/local/hbase*
# Create zookeeper directory (even if not needed)
sudo mkdir -p /usr/local/zookeeper
# Fix permission
sudo chown -R hduser:hadoop /usr/local/zookeeper
# Raise the limit for max opened files (DB srv)
sudo sysctl -w fs.file-max=100000
# Required due to -tt option
exit
EOF
done < /usr/local/hbase/conf/regionservers
That's the end of the journey: enjoy your new HBase cluster!
Start it running start-hbase.sh