Enhanced/Dual Powered
Willem EPROM Programmer
User Guide
Main Board / Cables
Main Board PCB3.5
Main Board PCB4E
Main Board PCB5.0
Main Board PCB5.5C
|
Parallel Data Cable (Printer extension cable, with male-female 25 pin connector, and pin to pin through) |
A-A type USB cable(for power) |
|
|
|
Optional Items:
|
ATMEL 89 Adapter |
ATMEL PLCC 44 Adapter |
TSOP 48 Adapter |
|
|
|
|
|
FWH/HUB PLCC32Adapter |
PLCC32 Adapter |
SOIC Adapter(Simplified) |
|
On-Board |
On-Board |
|
|
AC or DC Power Adapter (9V or 12V, 200mA) |
SOIC Adapter(Professional) |
|
|
|
|
|
Allows the computer to detect the phone in a "dead" state via a specific hardware key combination. Driver Technical Specifications Supported Device Nokia 130 (RM-1035) Chipset Architecture MediaTek (MTK) Driver Types Included
Nokia 130 Music (2025) - Leading Mobile Phone Distribution Company
: Automatically identified by Windows but often requires a manual update to match the hardware ID ( VID_0421&PID_069A Installation Guide for Windows 10/11 Modern Windows versions strictly enforce driver signature enforcement
If your computer still does not recognize the phone, try these solutions: nokia 130 rm1035 usb driver
often fails to connect properly to . Plug it into a USB 2.0 port instead.
Best for general connectivity, data transfer, and basic repairs.
Search for: “Nokia 130 RM-1035 USB Driver 7.1.7.1” – version 7.1.7.1 is the most stable for Windows 7 through 11. Allows the computer to detect the phone in
This is usually caused by using a "charge-only" Micro-USB cable. Ensure you are using a high-quality, 4-core data sync cable. Alternatively, try switching from a USB 3.0 port (blue) to a USB 2.0 port (black) on your PC. 2. Device Disconnects After 2 Seconds (VCOM Loop)
If you can tell me , I can provide a more specific installation guide .Alternatively, I can help you find a PC Suite that includes this driver automatically. Let me know!
Look at the Device Manager list. A new device will briefly appear under "Ports (COM & LPT)" or as an "Unknown Device" labeled MT65xx Preloader or MediaTek USB Device . It may disappear quickly; this is normal behavior for MTK bootloaders. Best for general connectivity, data transfer, and basic
: Since the RM-1035 uses a MediaTek (MTK) chipset, specific MTK VCOM or CDC drivers are necessary for flashing stock firmware or fixing software-related issues . Common Connection Use-Cases
For modern systems (Windows 10/11), you may need to to install older Nokia or MTK drivers : Nokia 130 (2023) USB Driver for Windows
Hardware Installation & Configuration
|
Installation Steps
(Note: the LPT port of PC MUST set to ECP or ECP+EPP during BIOS setup. To enter the BIOS setting mode, you need press "Del" key or "F1" key during the computer selftest, which is the moment of computer just power up.)
Software Version To Use | |||
| |||
|
| |||
|
The software interface:
| |||
|
| |||
|
Hardware
Check
| |||
|
PCB3.5/PCB4E
PCB5.0
PCB5.5C
Note: the Vcc setting jumper only has effect when you are using AC adaptor as power source. For the USB power only 5V Vcc is available. For the PCB5.5C, set DIP steps: 1. press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF. 2. press DIP Bit shift button to shift the DIP bit position to where need to set. And then press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF. 3. Repeat those steps till all DIP bit ae set same as software indicated. For PCB5.5C voltage and Special chip selection: 1. Put back the safety jumper. 2. Press the voltage button and hold for 1 second, the voltage LED should move to next. Repeat till desired voltage LED light up. 3. Press the chip selection button and hold for 1 second, the chip LED should move to next. Repeat till desired LED light up. 4. Remove the safety jumper to lock the selected voltage and chip selection DIP Switch (PCB3.5, PCB5.0)
When programming one chip, follow the program prompt to set DIP switch .
|
Allows the computer to detect the phone in a "dead" state via a specific hardware key combination. Driver Technical Specifications Supported Device Nokia 130 (RM-1035) Chipset Architecture MediaTek (MTK) Driver Types Included
Nokia 130 Music (2025) - Leading Mobile Phone Distribution Company
: Automatically identified by Windows but often requires a manual update to match the hardware ID ( VID_0421&PID_069A Installation Guide for Windows 10/11 Modern Windows versions strictly enforce driver signature enforcement
If your computer still does not recognize the phone, try these solutions:
often fails to connect properly to . Plug it into a USB 2.0 port instead.
Best for general connectivity, data transfer, and basic repairs.
Search for: “Nokia 130 RM-1035 USB Driver 7.1.7.1” – version 7.1.7.1 is the most stable for Windows 7 through 11.
This is usually caused by using a "charge-only" Micro-USB cable. Ensure you are using a high-quality, 4-core data sync cable. Alternatively, try switching from a USB 3.0 port (blue) to a USB 2.0 port (black) on your PC. 2. Device Disconnects After 2 Seconds (VCOM Loop)
If you can tell me , I can provide a more specific installation guide .Alternatively, I can help you find a PC Suite that includes this driver automatically. Let me know!
Look at the Device Manager list. A new device will briefly appear under "Ports (COM & LPT)" or as an "Unknown Device" labeled MT65xx Preloader or MediaTek USB Device . It may disappear quickly; this is normal behavior for MTK bootloaders.
: Since the RM-1035 uses a MediaTek (MTK) chipset, specific MTK VCOM or CDC drivers are necessary for flashing stock firmware or fixing software-related issues . Common Connection Use-Cases
For modern systems (Windows 10/11), you may need to to install older Nokia or MTK drivers : Nokia 130 (2023) USB Driver for Windows
